It is this one i want to make, i just do not have the dimentions.
https://www.ebay.com/itm/305662234630?_trkparms=amclksrc%3DITM%26aid%3D1110006%26algo%3DHOMESPLICE.SIM%26ao%3D1%26asc%3D271014%2C271291%26meid%3D9051b34df8f048019f2459742ba1c0c9%26pid%3D101875%26rk%3D1%26rkt%3D4%26sd%3D284468227124%26itm%3D305662234630%26pmt%3D1%26noa%3D0%26pg%3D2332490%26algv%3DSimplAMLv11WebTrimmedV3MskuWithLambda85KnnRecallV1V2V4ItemNrtInQueryAndCassiniVisualRankerAndBertRecallWithVMEV3EmbeddedAuctionsCPCAutoWithCassiniEmbRecallManualCVRShadow%26brand%3DUnbranded%252FGeneric&_trksid=p2332490.c101875.m1851&itmprp=cksum%3A3056622346309051b34df8f048019f2459742ba1c0c9%7Cenc%3AAQAJAAABkGjWmJM3XlNBfm3pn9GuNq%252BGWKzd5GI3fOSRV0RJa0PIUtbjiU5SKzZJcUtz6RJRXhEwjjacoLRnvLh84yQ2WYnZmbF9wrEKBX6G9Arc3QGXnOP5fdmSHfRgavVI82R07t%252BnUJXzuIQ%252BD5QyF1lfNuIGqAWM4e5yVzNQot0tleTAcudluOBjqFCfQOS9bJeOlfVe3pKy46zjWepWZKYQhX38HpGQ99SbBl3ljjDasrUB%252F2cS0XNRFJyKJE0%252FTMdTVn49QUalW0CPL5AVDmO%252Fvv43N%252FnPqVAKlArExdQsJm13i8%252FBZ7rgik92ZQjMI9PYFdVt%252FjoiWUAJTIOl9udyZ8NcgG7S7gOmMRWHc4zEK8hLMa1ILJ7sOalLrDd1eXT9IRz61SBywGu9oUERajC237KG2gxMn6WpcVWCSBrcnvsCHnwxpkyGHrg4nMlFbNNxDofDcccTvy5jl4sLF44gqpxtN7oalEBH%252FJxyYCLys7ah6jC6cOYcdX24MSGKLmvWr37MjVZQvUTU3JR5W1mF%252FoE%253D%7Campid%3APL_CLK%7Cclp%3A2332490&itmmeta=01J4PHE1FMVJVBSTDHJVXHCNYM

Hi, i have a RAD Power bike, model 2019 in my summer house, and i want to make a protection cover for the wire connectors that are situated under the bike under the pedals, and very exposed to water, stones, and other physical damage..
I know i can buy it, bur does anyone have a DIY suggestion, with measures, i could measure it myself, but i am away from my bike these days, and i want to make it and install it when i am back in my summer house.

It is the little reader, with the red LED that sit next to the plastic disk with the magnets, thats called the PAS sensor, and a wire with a small 3 pin plug comes out of it.
Thats the one i need to buy somewheree, but where?

hello, actually it is not the palstic disk with the magnets i need, it is the little sensor with the magnet sensor and the yello inside plug, i need to replace, the one that reads the magnet pulses from the plastic ring with the magnets.

Anyone know where i can buy a replacement PAS sensor for my Rad Rhino (Rover) from 2019, in Europe, i think it is broken?
 

Hello, i am seeking a new rear brake cable for my 2019 Rad Rhino bike, any suggestion to where i can order this i Europe?
Kind regards
Martin Olesen
Denmark

Hi,
I do not have my radrhino (radrover) at the place where i am now, but i need to buy some tools to repair the brakes on my bike.
Does anyone remember the specs for the two hex screws that hold the disk brake to the bike frame, i think it is 6 mm, or am i wrong, and how long are they?

Hi handelbar,
That is excatly how i will do i, but it will be next year, since the bike is here in my summerhouse, and we are leaving today 😀, but thanks for all your help!
Kind regards
Martin

Thank you for further info handelbar.
I may have found out what the problem could be, it i like when i activate the rear brake, one end of one of the brake pad, do not reach the disc, meaning that the two brake pads on each side of the disc, only use a part of surface to brake, and that limit the brake power.......if this  make sense......i need to try to adjust this.

Hi handlebar and Ddaybc,
Thank you very much for your very detailed explanation, i tried to adjust like yoy explain, but the brake still do not really block nice, like the front brakes, the backbrake is still very weak, is is strange with such a simple construction?.maybe it is because the cable to the back brake is longer, and there by more stretched, and thereby lot of the power are lost in stretch instead of being transfered to the brake?.

Hello,
I went on my Radrover, and found that the rearwheel break only brake very weak.
I tried to adjust them, but still not good brake power.
Then i changed the brakepads with new one......still now good, only very moderate brake function.
Has anyone observed similar, and how did you fix it?
The disk seems very clean, shall i try to clean it or sand it?

Hello,
We have a RadRhino (RadRover), and a RadRunner, and somethimes we would like to bring them with us, on tour with our car.
Can a standard rear car hook carry a RadRover and a RadRunner at the same time, and is there a recommendation for a rear rack for such two bikes, in Europe?

Actually i just want to buy the original Rad motor, i do not need the upgrade.

Hello,
Does anyone know if it is possible to buy a replacement plugin, plug and play, hub motor for a 2019 RadRhino bike, in europe, Rad only offer a complete rear wheel  including hubmotor.

Regards
Martin Olesen

Hi,
I got a older 2019 Radrover from a friend, i think the hubmotor is burned off, or the cable harness is sick.
Does anybody know if Rad sells rear wheel with motor as sparepart, and also the wireing harness, in Europe, and does anybody knows what it cost?